Do You like your car? It deserve for a properly tretment in a good car service

to the pistons; it contains short ducts (the ports) for intake and exhaust and the associated intake valves that open to let the cylinder be filled with fresh air and exhaust valves that open to allow the combustion gases to esca

Do You like your car? It deserve for a properly tretment in a good car service reduce smoke Citroen

2-stroke crankcase

The cylinder head is attached to the engine block by numerous bolts or studs. It has several functions. The cylinder head seals the cylinders on the side opposite to the pistons; it contains short ducts (the ports) for intake and exhaust and the associated intake valves that open to let the cylinder be filled with fresh air and exhaust valves that open to allow the combustion gases to escape. However, 2-stroke crankcase scavenged engines connect the gas ports directly to the cylinder wall without poppet valves; the piston controls their opening and occlusion instead. The cylinder head also holds the spark plug in the case of spark ignition engines and the injector for engines that use direct injection. All CI engines use fuel injection, usually direct injection but some engines instead use indirect injection. SI engines can use a carburetor or fuel injection as port injection or direct injection. Most SI engines have a single spark plug per cylinder but some have 2. A head gasket prevents the gas from leaking between the cylinder head and the engine block. The opening and closing of the valves is controlled by one or several camshafts and springs?or in some engines?a desmodromic mechanism that uses no springs. The camshaft may press directly the stem of the valve or may act upon a rocker arm, again, either directly or through a pushrod.
Engine block seen from below. The cylinders, oil spray nozzle and half of the main bearings are clearly visible.

The crankcase is sealed at the bottom with a sump that collects the falling oil during normal operation to be cycled again. The cavity created between the cylinder block and the sump houses a crankshaft that converts the reciprocating motion of the pistons to rotational motion. The crankshaft is held in place relative to the engine block by main bearings, which allow it to rotate. Bulkheads in the crankcase form a half of every main bearing; the other half is a detachable cap. In some cases a single main bearing deck is used rather than several smaller caps. A connecting rod is connected to offset sections of the crankshaft (the crankpins) in one end and to the piston in the other end through the gudgeon pin and thus transfers the force and translates the reciprocating motion of the pistons to the circular motion of the crankshaft. The end of the connecting rod attached to the gudgeon pin is called its small end, and the other end, where it is connected to the crankshaft, the big end. The big end has a detachable half to allow assembly around the crankshaft. It is kept together to the connecting rod by removable bolts.

The cylinder head has an intake manifold and an exhaust manifold attached to the corresponding ports. The intake manifold connects to the air filter directly, or to a carburetor when one is present, which is then connected to the air filter. It distributes the air incoming from these devices to the individual cylinders. The exhaust manifold is the first component in the exhaust system. It collects the exhaust gases from the cylinders and drives it to the following component in the path. The exhaust system of an ICE may also include a catalytic converter and muffler. The final section in the path of the exhaust gases is the tailpipe.

Źródło: https://en.wikipedia.org/wiki/Internal_combustion_engine


Who is interested in motorcycles?

Among those interested in the automotive industry is no shortage of people for whom motorbikes are the main area of interest. These are mainly young men, who do not yet have enough other expenses that can not afford to have a motorcycle. Although for many motorcycles is a passion for life, many a rider is forced in the future to replace your equipment, for example, disputes family car. However, the biggest enthusiasts of this equipment remain true to the end of his beloved motorcycle, so participants rallies for motorcyclists we can see a variety of people, not only of all ages, but also of different sexes. Women sometimes have the interest, though certainly more women have other, more feminine hobby.


Tuning car

Continuous improvement car is quite popular, especially among younger car owners. Many a young man invests a lot in order to have a truly unique car. True, knowing the automotive industry can be on their own to carry out less complicated tuning the car, but in many cases it is necessary to use the assistance of specialized auto mechanics and so on. Why deal with the improvement of the car? First of all, when we consider the car after tuning, we can see that their value increases considerably. Many modernized car looks almost like new, even if they already have a fairly high mileage and are quite age.